Solution to slag inclusion in lost foam casting(2)

3.1 The role of the lost foam coating is:
3.11 Improve the surface finish of castings, reduce the roughness of castings by 2-3 levels, and improve the surface quality and performance of castings.
3.12 Reduce and prevent sand sticking and sand hole defects.
3.13 is conducive to sand removal and falling sand.
3.14 The liquid and gas melted in the lost mold during pouring are smoothly discharged into the casting sand through the coating layer, and the molten metal is prevented from penetrating into the sand mold, preventing the casting from producing pores, metal penetration and carbon defects.
3.15 Improve the strength and rigidity of the pattern, prevent deformation and damage during transportation, sand filling and vibration modeling, and help improve the dimensional accuracy and yield of castings. Coatings for lost foam casting require a series of strength, air permeability, refractoriness, thermal insulation, explosion resistance and crack resistance, rapid cooling and rapid heat resistance, moisture absorption, cleaning, coating, suspension, non-flowing, etc. Performance, to prevent slag inclusion defects, first requires the coating to have high strength and fire resistance. It is required that the coating layer on the surface of the white mold does not crack or crack during the drying and transportation process, that is, the coating should have sufficient room temperature strength; and during the pouring process, the coating layer will also If it does not fall off or cracks, it has high high temperature strength. When the liquid metal enters the mold, the straight gate is tightly closed, and the coating layer on the surface of the casting and the pouring system does not fall off, cracks and cracks are the primary conditions to prevent slag inclusion defects. If the runner is not tightly sealed, the coating layer will fall off. Cracks and cracks, a large amount of sand, paint and inclusions will enter the metal to form slag inclusion defects. Strength and air permeability are two important properties of coatings. Sometimes the coatings used in the pouring system are required to have higher fire resistance than the casting coatings to resist the long-term erosion of high-temperature metals without falling off and cracking. The operator must ensure the uniformity of the paint during the painting process.

3.2 Packing operation
During packing, the coating layer on the surface of the pattern group (model + gating system) is not allowed to have any shedding, cracks or cracks, especially at the junction of the sprue and the runner, the junction of the runner and the inner runner, and the inner As long as there is looseness, cracks, or weak connection between the gate and the mold, sand may enter. This requires high joint strength, thicker paint, sufficient rigidity for the gating system, and braces or reinforcement sleeves when necessary. The pattern group should be stable when placed on the bottom sand of the sand box. It is not allowed to start sanding and vibration modeling when it is placed in the air to avoid shock cracking of the coating layer. Don''''''''''''''''t add sand directly to the appearance, use a hose to add sand first, and then use the rain shower to sprinkle sand. When you start to shake the shape, the vibration should be slight and the amplitude should be small, and then vibrate greatly after the dry sand is buried in the shape. In the vibration molding, the pouring system, especially the sprue, is not allowed to break or bend, so as to prevent the coating layer from cracking, and the sprue must be tightly sealed to prevent sand from entering. The entire packing, sanding, vibration, and modeling operations must be very careful and careful, and it must be ensured that the coating layer of the pattern group does not fall off, cracks or cracks before pouring. Before pouring, the sprue cup should be cleaned again to ensure that there is no floating sand, dust and debris.

3.3 Pouring head, temperature and time
The higher the pressure head during pouring, the greater the erosion of the pouring system and the mold, and the greater the possibility of sand ingress caused by scouring the coating. The pressure head is different for castings of different sizes. To choose a ladle with appropriate capacity, the ladle should be as low as possible the pouring height, and the ladle mouth should be as close as possible to the pouring cup, and large ladle should be avoided for pouring small jobs. The higher the pouring temperature, the higher the performance requirements of the coating, and the easier it is to produce defects such as sticky sand and slag. The proper pouring temperature should be selected. For gray iron castings, the tapping temperature can be around 1480°C, and the pouring temperature should be 1380-1420°C; the tapping temperature of ductile iron castings should be above 1500°C, and the pouring temperature should be 1420-1450°C; the pouring temperature of steel castings should be 1480-1560°C . The pouring time of a box of iron castings requiring 300-500 kg of molten iron can be controlled within 10-20 seconds.

3.4 negative pressure
The pouring process of lost foam casting is generally carried out under vacuum conditions. The role of negative pressure is to compact dry sand, accelerate exhaust, and improve filling capacity. Pouring under vacuum sealing conditions improves the working environment. The degree of negative pressure has a great influence on the quality of castings. Excessive negative pressure increases the possibility of inhaling dry sand and inclusions when the molten metal flows through the cracks and cracks, and also increases the sticky sand defects of the castings. Too fast filling speed increases the scouring ability of the metal to the runner and the mold, and it is easy to cause the paint to fall off and enter the metal, and it is also easy to wash out the paint layer and cause sand to enter. For iron castings, the appropriate negative pressure is generally 0.025-0.04MPa.

3.5 Set up slag stop, slag skimming and slag collecting riser
Setting slag retaining and slag skimming in the gating system and setting slag collecting risers on the castings and taking slag retaining and slag skimming measures can help to improve the defects of sand and slag inclusion.

3.6 Molding sand
Too coarse and fine sand size will affect the occurrence of slag inclusion and sand sticking defects. Too coarse particle size will increase sand sticking and slag inclusion defects. Iron castings generally use dry quartz sand (washed sand) with a grain size of 30/50.

3.7 Using hot metal purification technology
The entire molding process of lost foam castings must consider the problem of molten iron purification, which is one of the key technologies of lost foam casting. The whole process including molten iron smelting, overheating, and pouring into the mold must consider the purification problem, and filtration technology is one of them.

Qingdao Sanzhuji Equipment Manufacturing Co., Ltd. specializes in the production of Green Sand Molding Line,Self-hardening sand molding line,foundry machines,Sand molding machine,Sand casting equipment,sand mixer,GS high efficiency rotary mixer,Resin sand mixer,no-bake resin sand mixer,Jolt squeeze molding machine/Jolt-squeezing moulding machines,Multi- Piston Moulding Machine/Hydraulic multi-piston moulding machine,sand casting molding machine,sand reclamation equipment，foundry molding machine,flaskless moulding machine,shot blasting machine,dust collector,according to the amount of old sand recovered Carry out plan customization, and provide sand reclamation equipment installation, commissioning, and training. Welcome guests to visit the factory.